We Say

The idea behind applying snow foam to your car before hand washing it is simple and the benefit is obvious. If you apply a blanket of detergent-rich foam to dirty surfaces and leave it to dwell for a while, it will progressively dissolve and suspend a lot of dirt and grime. When you then rinse it off, much of the dirt and grime is washed away with it, leaving relatively clean surfaces behind. Clearly, the benefit is that the bulk of dirt removal is done before you actually touch your car with a wash mitt, which greatly reduces the risk of inflicting marring and fine scratches during the subsequent hand-washing step. However, does the foam need to be thick to work properly? Many people think so, most likely because thick clinging foam is visually impressive. However, the reality is that thinner foams often work just as well. Bilt Hamber auto-foam is one such example. It's thinner than many of its rivals, but it cleans every bit as well, and its effective strength can be adjusted by varying its dilution rate. It's different, but in a good way. Recommended!

Key Features

Cleaning Strength9/10(Compared To Others)

Foaminess6/10(Compared To Others)

Recommended Dosage200 ml(In A PA Foam Lance)

Description

Bilt Hamber auto-foam is a highly concentrated pre-wash foaming agent that dissolves and carries away a large amount of dirt and grime in a completely touchless fashion. Although best suited to regular use and tackling relatively fresh contaminants, it is also powerful enough to tackle more persistent road films that have gone through multiple wetting and drying cycles and become more firmly bonded. The main ingredients in Bilt Hamber auto-foam are a blend of biodegradable and environmentally friendly surfactants, plus a powerful wetting agent. The latter is critical to the way Bilt Hamber auto-foam works, as it causes the bubbles in the foam to systematically burst as it moves over the car, enabling the surfactants to progressively soak and suspend the accumulated dirt and grime. As you might expect, this formula effectively lifts dirt and grime without stripping existing sealant or wax protection, and is safe for use on all exterior surfaces, including bare metals and other sensitive trims.

Specification

More Information
Chemical Basis	Detergent-based
Cleaning Strength	9
Foaminess	6
Maximum Dwelling Time	5 minutes
Recommended Dilution Ratio	50:1 (water:product)
Recommended Dosage	200 ml (in a PA Foam Lance)
Size	5L & 25L
Strips Coatings	No
Strips Sealants And Waxes	No
pH	13 (alkaline)

How To Use

Bilt Hamber auto-foam is suitable for use in any foam gun or foam lance system, as long as a final dilution ratio of approximately 50:1 (water:product) can be achieved. With regard to the systems we offer, the following advice applies: (i) for use with a PB Foam Gun, remove the foam gun body and pour or pump approximately 400 ml of Bilt Hamber auto-foam into the bottle, then fill the bottle to the top with hot water, refit the foam gun body and shake the whole unit gently to mix the solution before finally attaching it to your hose - then squeeze the trigger and adjust the top dial on the foam gun body until you get the desired foam thickness; (ii) for use with a PA Foam Lance, remove the foam lance body and pour or pump approximately 200 ml of Bilt Hamber auto-foam into the bottle, then fill the bottle to the top with hot water, refit the foam lance body and shake the whole unit gently to mix the solution before finally attaching it to your pressure washer - then fire the washer up, and adjust the top dial on the foam lance body until you get the desired foam thickness. In both examples given above, you can safely double the amount of Bilt Hamber auto-foam used when tackling particularly dirty cars, or else halve it if only a light clean is needed.

We Say

Key Features

Description

Specification

How To Use

Reviews

We Say

Key Features

Description

Specification

How To Use

Snow Foams & Equipment

Filters

Bilt Hamber Auto Foam